IP static routes remain in the IP route table only so long as the IP interface to the next-hop router is up. If the next-hop interface goes down, the software removes the static route from the IP route table. If the next-hop interface comes up again, the software adds the route back to the route table.

Setting Up a Typing Break; 2. Date and Time Configuration. Static routes set using ip commands at the command prompt will be lost if the system is shutdown or When you expand IPv4 Routes Table, you should see Local routes with the IP addresses you have configured on the VLANs. This means routing is fully enabled for those VLANs. Setting up Static Routes. To configure static routes on the switch, make sure you are in Network Administration > Route settings > IPv4 Route Settings; Click Edit; Click Add To do this, you need to add a static route. Add a temporary static route. If you wish to add one temporarily, simply run the ip route add command with the right network information: ip route add 172.16.5.0/24 via 10.0.0.101 dev eth0. 172.16.5.0 is the network you wish to access. /24 is the subnet mask 10.0.0.101 is the secondary router to which I set up the route just fine in the Verizon router, however when I try to set up the complementary route in the E4200 I get "invalid static route". In the Verzion Router, I define: Destination: 192.168.2.0 -< Subnet containing the E4200 and the rest of my network Connect via telnet and set the route manually via "ip route" or "route" Add to /etc/rc.local to set them to be static. There is a file, /var/StaticRoutesList, where I can see routes from the web interface being added, but not sure if that one can be modified. I tried to add a static route in there but it would not show up in the web interface To create a static route in the routing table, you must, atminimum, define the route as static and associate a next-hop addresswith it. The static route in the routing table is inserted into theforwarding table when the next-hop address is reachable.

Static routes or routes learned by dynamic protocols have to be configured in order for the routers to do their job: Routing packets of course. Also keep in mind that default routes are chosen when there is no specific match in the routing table to a given network.

When you expand IPv4 Routes Table, you should see Local routes with the IP addresses you have configured on the VLANs. This means routing is fully enabled for those VLANs. Setting up Static Routes. To configure static routes on the switch, make sure you are in Network Administration > Route settings > IPv4 Route Settings; Click Edit; Click Add To do this, you need to add a static route. Add a temporary static route. If you wish to add one temporarily, simply run the ip route add command with the right network information: ip route add 172.16.5.0/24 via 10.0.0.101 dev eth0. 172.16.5.0 is the network you wish to access. /24 is the subnet mask 10.0.0.101 is the secondary router to which

To illustrate static routing the example will be a small network with two routers and two workstations, with the workstations placed on the far ends of the network. On it, the routers are configured so that the FastEthernet 0/0 (fa0/0) interfaces are for the computer side of the network and the FastEthernet 0/1 (fa0/1) interfaces …

I set up the route just fine in the Verizon router, however when I try to set up the complementary route in the E4200 I get "invalid static route". In the Verzion Router, I define: Destination: 192.168.2.0 -< Subnet containing the E4200 and the rest of my network Connect via telnet and set the route manually via "ip route" or "route" Add to /etc/rc.local to set them to be static. There is a file, /var/StaticRoutesList, where I can see routes from the web interface being added, but not sure if that one can be modified. I tried to add a static route in there but it would not show up in the web interface To create a static route in the routing table, you must, atminimum, define the route as static and associate a next-hop addresswith it. The static route in the routing table is inserted into theforwarding table when the next-hop address is reachable. Branch#show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, o - ODR, P - periodic downloaded IP static routes remain in the IP route table only so long as the IP interface to the next-hop router is up. If the next-hop interface goes down, the software removes the static route from the IP route table. If the next-hop interface comes up again, the software adds the route back to the route table.